At first developed to mimic a classic look (as identified on very old violins and mandolins) Sunburst is a classic guitar color frequently encountered upon guitars aged and newer. It's a highly desirable guitar finish but it it possible for the average person? It is possible to obtain a sunburst finish on your own guitar if you decide to follow a couple of basic steps and take your time and don't rush. It's wise for you to experiment first using a scrap part of lumber prior to moving on to the guitar.
If it is a brand new guitar kit,then construct your guitar firstly. Needless to say you will be pulling it down to work on the finish but you need to know you won't befacing potential issues with the guitar that jeopardize the finish you've specifically put a great deal of valuable time into. When you've constructed the electric guitar and analyzed for potential problems you should begin to set up the timber. Sand right back until eventually you get a totally consistent surface to apply your finish. You should get rid of unwanted dust particles and clean the guitar completely.
Next administer some timber grain filler. You'll want to apply evenly over the face of your guitar and afterwards work it in to the grain. Once dried out remove the excess and remove excess with a moistened scrap of material. Now it is the time to spray the back and sides of the body and neck of your electric guitar. A fundamental point to take into account would be to mask the top and neck. As you're spraying paint or lacquer it's best if you keep the spray cans in warm water before you start using. It's going to demand a number of coats as a consequence do not consider applying too much all at once. The trick will be to build up your guitar's tone layer upon layer and apply from a reasonable distance away so you attain a feathered edge. The closer you get the harder the edge line you will end up with.
Following that administer the amber lacquer. Chances are you'll need to mask the sides of the guitar and then position the guitar on the strong workbench face up before you commence. If you have completed this step you can administer the clear coat afterwards and sand between coats to eliminate any potential problems. After that administer your next pitch-dark stain to acquire a transition of colour within the edge and inner colours. Consider applying very thin and amass the required coats. At this point it's best to let the guitar dry out. As soon as the guitar is perfectly dried out begin sanding all over again.
This is the very last part. The trick here is to make use of a more lightweight gauge of sand paper every time as you get in a nutshell taking out the marks because of the gauge of sandpaper used beforehand soon after which progressing which has a lighter gauge. Continue to keep delicately sanding after that migrating to a lighter gauge if you do not run out of sandpaper after which you can move on to your buffer.About now you can basically continue to keep buffing or hand polishing until you end up getting completely fine with the finished look.
If it is a brand new guitar kit,then construct your guitar firstly. Needless to say you will be pulling it down to work on the finish but you need to know you won't befacing potential issues with the guitar that jeopardize the finish you've specifically put a great deal of valuable time into. When you've constructed the electric guitar and analyzed for potential problems you should begin to set up the timber. Sand right back until eventually you get a totally consistent surface to apply your finish. You should get rid of unwanted dust particles and clean the guitar completely.
Next administer some timber grain filler. You'll want to apply evenly over the face of your guitar and afterwards work it in to the grain. Once dried out remove the excess and remove excess with a moistened scrap of material. Now it is the time to spray the back and sides of the body and neck of your electric guitar. A fundamental point to take into account would be to mask the top and neck. As you're spraying paint or lacquer it's best if you keep the spray cans in warm water before you start using. It's going to demand a number of coats as a consequence do not consider applying too much all at once. The trick will be to build up your guitar's tone layer upon layer and apply from a reasonable distance away so you attain a feathered edge. The closer you get the harder the edge line you will end up with.
Following that administer the amber lacquer. Chances are you'll need to mask the sides of the guitar and then position the guitar on the strong workbench face up before you commence. If you have completed this step you can administer the clear coat afterwards and sand between coats to eliminate any potential problems. After that administer your next pitch-dark stain to acquire a transition of colour within the edge and inner colours. Consider applying very thin and amass the required coats. At this point it's best to let the guitar dry out. As soon as the guitar is perfectly dried out begin sanding all over again.
This is the very last part. The trick here is to make use of a more lightweight gauge of sand paper every time as you get in a nutshell taking out the marks because of the gauge of sandpaper used beforehand soon after which progressing which has a lighter gauge. Continue to keep delicately sanding after that migrating to a lighter gauge if you do not run out of sandpaper after which you can move on to your buffer.About now you can basically continue to keep buffing or hand polishing until you end up getting completely fine with the finished look.
About the Author:
Before you buy anything, check our website at www.eguitarkits.com for information related to Guitar Kits and tips and tricks on getting a good finish.
